You'll be asked 2 vehicle safety questions. These are also known as the 'show me, tell me' questions.
Very simply, the examiner will ask you one 'show me' question, where you'll have to show them how you'd carry out a vehicle safety check and one 'tell me' question, where you'll need to explain to the examiner how you'd carry out the check.
Although some checks may involve the candidate opening the bonnet to identify where fluid levels would be checked, pupils will not be asked to touch a hot engine or physically check fluid levels.
These basic safety checks are necessary for drivers to ensure the vehicle is safe for use. Although good driving instructors will show their students the procedures useful material can be found in the DVSA publication 'The official guide to Driving - the essential skills' and 'The official DVSA guide to learning to drive'. Further advice and information on how to carry out vehicle safety checks can also be found in the manufacturer's handbook.
The examiner will ask the pupil 2 of the following questions at the beginning of their test. If the pupil answers one or both questions incorrectly then, one driving fault will be recorded, which will count towards, the maximum of 15 driving faults allowed.
Remember, whilst you are required to demonstrate an understanding of these checks and that the vehicle is safe, you are not expected to answer parrot fashion, using the exact terminology.
Open the bonnet, identify where you would check the engine oil level and tell me how you would check that the engine has sufficient oil. Identify dipstick/oil level indicator, describe check oil level against the minimum/maximum markers.
Open the bonnet, identify where you would check the engine coolant level and tell me how you would check that the engine has the correct level. Identify high/low level markings on header tank where fitted or radiator filler cap, and describe how to top up to correct level.
Identify where the windscreen washer reservoir is and tell me how you would check the windscreen washer level.Identify reservoir and explain how to check level.
Open the bonnet, identify where the brake fluid reservoir is and tell me how you would check that you have a safe level of hydraulic brake fluid.Identify reservoir, check against high/low markings.
Tell me how you would check that the brake lights are working on this car. (I can assist you, if you need to switch the ignition on, please don't start the engine.Operate brake pedal, make use of the reflections in windows, garage doors, etc, or ask someone to help.
Tell me how you would check that the brakes are working before starting a journey. Brakes should not feel spongy or slack. Brakes should be tested as you set off. Vehicle should not pull to one side.
Tell me how you would check the tyres to ensure that they have sufficient tread depth and that their general condition is safe to use on the road. No cuts and bulges, 1.6mm of tread depth across the central ¾ of the breadth of the tyre and around the outer circumference.
Tell me where you would find the information for the recommended tyre pressures for this car and how tyre pressures should be checked. Manufacturer's guide, use a reliable pressure gauge, check and adjust pressures when tyres are cold, don't forget spare tyre, remember to refit valve caps.
Show me/explain how you would check that the power assisted steering is working before starting a journey. If the steering becomes heavy the system may not be working properly. Before starting a journey two simple checks can be made. Gentle pressure on the steering wheel, maintained while the engine is started, should result in a slight but noticeable movement as the system begins to operate. Alternatively turning the steering wheel just after moving off will give an immediate indication that the power assistance is functioning.
Tell me how you would check that the headlights and taillights are working. (No need to exit the vehicle). Operate switch (turn on ignition if necessary), walk round vehicle.
Show me how you would check that the direction indicators are working. Applying the indicators or hazard warning switch and check functioning of all indicators.
Show me how you would check that the horn is working (off road only). Check is carried out by using control (turn on ignition if necessary).
Show me how you would check the parking brake (handbrake) for excessive wear, make sure you keep safe control of the vehicle. Demonstrate by applying parking brake that when it is fully applied it secures itself, and is not at the end of the working travel.
Tell me how you make sure your head restraint is correctly adjusted so it provides the best protection in the event of a crash. The head restraint should be adjusted so the rigid part of the head restraint is at least as high as the eye or top of the ears, and as close to the back of the head as is comfortable. NB. Some restraints might not be adjustable.
Show me how you would clean the windscreen using the windscreen washer and wipers. Operate control to wash and wipe windscreen (turn ignition on if necessary)
Show me how you would set the demister controls to clear all the windows effectively, this should include both front and rear screens. Set all the relevant controls including; fan, temperature, air direction/source and heated screen to clear windscreen and windows. Engine does not have to be started for this demonstration.
Show me how you would switch on the rear fog light(s) and explain when you would use it/them. (Not need to exit vehicle) Operate switch (turn on dipped headlights and ignition if necessary). Check warning light is on. Explain use.
Tell me how you would know if there was a problem with your anti lock braking system. Warning light should illuminate if there is a fault with the anti lock braking system.
Show me how you switch your headlight from dipped to main beam and explain how you would know the main beam is on whilst inside the car. Operate switch (with ignition or engine on if necessary), check with main beam warning light.